The Controller GSM v4.2 is a small device with many possibilities. It can send sensor readings or execute on\/off commands via SMS, connection, MQTT (via GPRS data transmission to server or application). The device also has the function of automating actions and sending notifications as a result of events or reaching a value.
\nA distinctive feature of the new GSM Controller is the configuration via the website. No additional cables, driver installation or special software are needed. The customer simply inserts the SIM card, turns on the device, logs into his account and, by entering his device identification number for the first time, adds it to his list of devices. Further settings are made through the configuration page on the mqtt.ats.pl server. The website uses the MQTT protocol to communicate with the device using GPRS data transmission. In the event that the SIM card does not use the default Internet access settings, we inform you in the installation procedure how to change the device settings via SMS.
\nModes of operation:<\/p>\n
Control by connection from an authorized number (in effect, it will turn on the relay and, for example, open the gate).
\n Control and receive information via SMS.
\n Controlling and receiving data by the server using the mqtt protocol.
\n Local automation using the conditions set on the device, which may result in e.g. switching on the output depending on the sensor reading. <\/p>\n
NOTE: The GSM controller can work in all these modes simultaneously
\nEquipment:<\/p>\n
2 analog inputs: for the 0-5V and 0-33V range, for measuring voltage, direct current (additional sensors needed), temperature sensors, photoresistors – dusk sensor, pressure sensor and many others
\n Digital input in 1-Wire standard – measurement of up to 8 DS18B20 temperature probes
\n Digital input in I2C standard – for many different sensors or expansion of outputs
\n Serial bus (UART 3.3V)
\n 2 logic inputs – as a status monitor (open\/close doors, PIR sensors, etc.), as a manual switch button
\n 1 relay (NO, C, NC)
\n Measurement of supply voltage and temperature on the board <\/p>\n
Software:<\/p>\n
Configuration via website
\n Support for SMS commands and notifications
\n Changing the starting state by making a call from an authorized number
\n Support for up to 100 numbers authorized for calling functions
\n Support for HTTP (GET) and MQTT communication protocols
\n Calibration of sensors
\n Calculation of the difference in readings from the inputs <\/p>\n
List of currently supported sensors and devices:<\/p>\n
Analog inputs (voltage measurement in the range of inputs, other supported in the software)
\n DC current sensor: ACS711EX_15, ACS711EX_30, ACS709_75, ACS711LC_12, ACS711LC_25, ACS711LC20, WCS1800, LA100P, R = 0.1\u2126, R = 0.01\u2126, R = 0.05\u2126
\n Logic inputs (digital)
\n magnetic sensor to open the door, etc.
\n 1-Wire bus
\n DS18B20 temperature sensor
\n I2C bus
\n humidity sensors: BME280 (humidity, temperature, atmospheric pressure)
\n SPS30 particle sensor (PM1, PM2.5, PM4, PM10)
\n OUT1-4 PCF8574 output extension
\n Serial port
\n MH-Z16, MH-Z19 CO2 sensors
\n GMQ125 ozone sensor
\n MODBUS port (via an additional RS485 converter)
\n 2-way energy meters SDM120M and SDM72D-M (readings for power, energy, voltage, current and other parameters depending on the meter)
\n Danfos EKC 202C controller <\/p>\n","protected":false},"excerpt":{"rendered":"
Top \u00bb Power Supply & PoE \u00bb Controllers and restarters \u00bb TC-GSMKON-040
\nGSM Controller V4.2
\nCode: \tTC-GSMKON-040
\nProduct model: \tGSMKON-040
\nStock:\tin stock in stock
\nAddThis Sharing Buttons
\nShare to Facebook
\nShare to TwitterShare to Email AppShare to PrintShare to More
\nQuantity
\nor
\nOrder Total\t1+ \t10+ \t20+ \t50+ \t100+ \t200+ \t500+ \t1000+
\n \t600 EUR \t1200 EUR \t3000 EUR \t6000 EUR \t15000 EUR \t30000 EUR
\nPrice\t55.51 EUR\t54.48 EUR\t53.45 EUR\t52.66 EUR\t51.88 EUR\t51.30 EUR\t50.73 EUR\t50.15 EUR
\n\tAsk a question about
\nthis product…
\nTiny control
\nThe Controller GSM v4.2 is a small device with many possibilities. It can send sensor readings or execute on\/off commands via SMS, connection, MQTT (via GPRS data transmission to server or application). The device also has the function of automating actions and sending notifications as a result of events or reaching a value.
\nA distinctive feature of the new GSM Controller is the configuration via the website. No additional cables, driver installation or special software are needed. The customer simply inserts the SIM card, turns on the device, logs into his account and, by entering his device identification number for the first time, adds it to his list of devices. Further settings are made through the configuration page on the mqtt.ats.pl server. The website uses the MQTT protocol to communicate with the device using GPRS data transmission. In the event that the SIM card does not use the default Internet access settings, we inform you in the installation procedure how to change the device settings via SMS.
\nModes of operation:<\/p>\n
Control by connection from an authorized number (in effect, it will turn on the relay and, for example, open the gate).
\n Control and receive information via SMS.
\n Controlling and receiving data by the server using the mqtt protocol.
\n Local automation using the conditions set on the device, which may result in e.g. switching on the output depending on the sensor reading. <\/p>\n
NOTE: The GSM controller can work in all these modes simultaneously
\nEquipment:<\/p>\n
2 analog inputs: for the 0-5V and 0-33V range, for measuring voltage, direct current (additional sensors needed), temperature sensors, photoresistors – dusk sensor, pressure sensor and many others
\n Digital input in 1-Wire standard – measurement of up to 8 DS18B20 temperature probes
\n Digital input in I2C standard – for many different sensors or expansion of outputs
\n Serial bus (UART 3.3V)
\n 2 logic inputs – as a status monitor (open\/close doors, PIR sensors, etc.), as a manual switch button
\n 1 relay (NO, C, NC)
\n Measurement of supply voltage and temperature on the board <\/p>\n
Software:<\/p>\n
Configuration via website
\n Support for SMS commands and notifications
\n Changing the starting state by making a call from an authorized number
\n Support for up to 100 numbers authorized for calling functions
\n Support for HTTP (GET) and MQTT communication protocols
\n Calibration of sensors
\n Calculation of the difference in readings from the inputs <\/p>\n
List of currently supported sensors and devices:<\/p>\n
Analog inputs (voltage measurement in the range of inputs, other supported in the software)
\n DC current sensor: ACS711EX_15, ACS711EX_30, ACS709_75, ACS711LC_12, ACS711LC_25, ACS711LC20, WCS1800, LA100P, R = 0.1\u2126, R = 0.01\u2126, R = 0.05\u2126
\n Logic inputs (digital)
\n magnetic sensor to open the door, etc.
\n 1-Wire bus
\n DS18B20 temperature sensor
\n I2C bus
\n humidity sensors: BME280 (humidity, temperature, atmospheric pressure)
\n SPS30 particle sensor (PM1, PM2.5, PM4, PM10)
\n OUT1-4 PCF8574 output extension
\n Serial port
\n MH-Z16, MH-Z19 CO2 sensors
\n GMQ125 ozone sensor
\n MODBUS port (via an additional RS485 converter)
\n 2-way energy meters SDM120M and SDM72D-M (readings for power, energy, voltage, current and other parameters depending on the meter)
\n Danfos EKC 202C controller <\/p>\n
Technical Specification:
\nPower Voltage \t5-55V
\nRelay \t125VAC 3A
\nAntenna \tSMA connector
\nSIM card \tnano SIM
\nOperating temperature range \t-20 to +55 \u00b0 C
\nDimensions \t69 x 40 x 29 mm (without DIN base and antenna)
\nWeight \t56g
\nKit contents \tGSM Controller in housing
\nDIN mounting base Antenna (omnidirectional, 2dBi gain)
\nPower cable (30cm with a plug – 2mm pitch)
\nShort hardware and configuration instructions <\/p>\n","protected":false},"featured_media":5844,"comment_status":"open","ping_status":"closed","template":"","meta":[],"product_cat":[146,41],"product_tag":[],"class_list":{"0":"post-5843","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-controllers-and-restarters","7":"product_cat-power-supply-poe","9":"first","10":"instock","11":"shipping-taxable","12":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/alb-link.al\/index.php?rest_route=\/wp\/v2\/product\/5843","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/alb-link.al\/index.php?rest_route=\/wp\/v2\/product"}],"about":[{"href":"https:\/\/alb-link.al\/index.php?rest_route=\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/alb-link.al\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=5843"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/alb-link.al\/index.php?rest_route=\/wp\/v2\/media\/5844"}],"wp:attachment":[{"href":"https:\/\/alb-link.al\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=5843"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/alb-link.al\/index.php?rest_route=%2Fwp%2Fv2%2Fproduct_cat&post=5843"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/alb-link.al\/index.php?rest_route=%2Fwp%2Fv2%2Fproduct_tag&post=5843"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}